mycarforum: 2014 Mazda 3 part 20

higher comp having more power/torque is true. �But often, it makes the peak figures at higher rpm.

The reverse is true for lower comp.

�

i c i c. smthg new about lower comp - always thot higher comp = more pwr.

�

[thumbsup] �Yup...this car will be perfect with abit more low-end torque...no choice must rev to 3k rpm & above at low gears...but fc suffer... [:(] . Best fc when rev <.2.2k rpm.�

�

higher comp having more power/torque is true. �But often, it makes the peak figures at higher rpm.

The reverse is true for lower comp.

�

�

Bro, did you place the passenger scuff plate wrongly to the driver side? Mine dont have wording, but I thought the wording shld be behind rather than forward? �

�

both piece of scuff plates are the same. so if i were to swap it to the opposite side, the wordings are in the opposite direction. my passenger side wordings are behind. now im thinking if i should remove the scuff plates. haha. does yours stick very well onto ur inner car?

Bro,

Where you get the carpet?

Cheers

Bro,

Where you get the carpet? Cheer

�

Mine was given by SE. perhaps thats why theres a mazda 3 logo there.

I've update my Navigation SD card with Mazda Toolbox recently. Today is the first time I take MCE and found out that there is no MCE data in the GPS. Like to check with the rest if the original GPS map has MCE? Not sure why the updates using Mazda toolbox dont have MCE inside... thks.
I've update my Navigation SD card with Mazda Toolbox recently. Today is the first time I take MCE and found out that there is no MCE data in the GPS. Like to check with the rest if the original GPS map has MCE? Not sure why the updates using Mazda toolbox dont have MCE inside... thks.

�
both piece of scuff plates are the same. so if i were to swap it to the opposite side, the wordings are in the opposite direction. my passenger side wordings are behind. now im thinking if i should remove the scuff plates. haha. does yours stick very well onto ur inner car?

Could it be that they gave you 2x passenger side scuff plates? My driver side and rear doors plates fit nicely. The passenger door plate was made for non i-Eloop model, so the front is slightly smaller abd I have to bent out the edge to fit it in. Now all fit nicely.

Could it be that they gave you 2x passenger side scuff plates? My driver side and rear doors plates fit nicely. The passenger door plate was made for non i-Eloop model, so the front is slightly smaller abd I have to bent out the edge to fit it in. Now all fit nicely.

�

perhaps they gave me both passenger side scuff plates. but i gotten it from taobao.so its slightly troublesome too to request them to change it. well. will just make do of the scuff plates. hope people dont realise the passenger and driver scuff plate are in the opposite direction.

�

where is the mzd toolbox u guys are talking about? how do u update the sd card. my SE told me nothing about the mzd toolbox

�
Mine was given by SE. perhaps thats why theres a mazda 3 logo there.

Can get from this shop. The lady boss told me Eurokars got it from them and I was told by my SE will cost around $60 if get it thru your SE.

http://m.sgcarmart.c...t.php?MID=14553

yes. Send to a�warehouse in US�(local agent)�and�ship to Singapore. Bought it on impulse. [bigcry]

�

Alternatively, I discovered Amazon also have a few (NOT ALL)�of the items; Free shipping & Delivery to S,pore�if you order >=US$125

�

I got most of the interior and exterior items via taobao: -

http://detail.tmall....?id=41865931591�(Most damage from this dealer; gd service; �they also�throw in freebies.
http://detail.tmall....?id=39682528836�(Avg service, but price quite competitive.)
http://item.taobao.c..._u=526p8ig221dc. (Ordered from them, but they could not ship to Singapore; need a third party to ship to Singapore.

�

How do you buy from Mazda USA? From the website?

�

�

�

Edited by Kiddies, 05 January 2015 - 08:07 PM.

Bro,
Where you get the carpet?
Cheers

Bro,
Where you get the carpet? Cheer

I bought from Maxtrending, 3M standard grade is $145, superior grade is $175. I think this is the only authorized 3M car mat shop locally...

http://www.maxtrend.com.sg/index.htm

Edited by Brainstorm, 05 January 2015 - 08:26 PM.

�
where is the mzd toolbox u guys are talking about? how do u update the sd card. my SE told me nothing about the mzd toolbox

I download from a Mazda USA link posted here in the forum. But today went MCE and realize MCE not in the map.. wonder if the original GPS has MCE or not?

Edited by Brainstorm, 05 January 2015 - 08:56 PM.

Can get from this shop. The lady boss told me Eurokars got it from them and I was told by my SE will cost around $60 if get it thru your SE.

http://m.sgcarmart.c...t.php?MID=14553

I was charged $70 for�3 pieces. $60 for�5 pieces (�3 pieces for the rear instead of 1 long one).

I download from a Mazda USA link posted here in the forum. But today went MCE and realize MCE not in the map.. wonder if the original GPS has MCE or not?

�

There is no MCE in the original map.. i am still on the original maps and i am always driving in the sea when in MCE..

Can get from this shop. The lady boss told me Eurokars got it from them and I was told by my SE will cost around $60 if get it thru your SE.

http://m.sgcarmart.c...t.php?MID=14553

�

You already paid a hefty sum for the car bro.. Get SE to throw it in free..

�
There is no MCE in the original map.. i am still on the original maps and i am always driving in the sea when in MCE..

Thanks. But I realize something weird, the M3 GPS seems to have INS, cos my GPS location is moving in blank map space when I'm in MCE and the GPS location also turned when I turned... but when I exited the tunnel, the position is slightly off from actual location. Do you notice the same thing?

I going to try again tmr...

Thanks. But I realize something weird, the M3 GPS seems to have INS, cos my GPS location is moving in blank map space when I'm in MCE and the GPS location also turned when I turned... but when I exited the tunnel, the position is slightly off from actual location. Do you notice the same thing?

I going to try again tmr...

�

Yeah, same here.. So the issue is that the map is not updated.. heard that this not-so-updated map was around since the first stocks of M3 was delivered to Sg.. so i think nothing has changed ever since..

Any contacts that sell such reliable and compatible refills at reasonable price?

To tell the truth i haven read the manual yet.. haha i just left the black folder in the glove compartment the day i got the car.. paiseh didn't ask them abt the programming of auto lock but i thought i didn't want it since in order to unlock i'd have to flick the lock as there is no switch for easy lock/unlock above the window switches..

From some other link in this forum, one of the bro good work for Mazda stock list:

Company Name : CHIN HON MOTOR & TRADING PTE LTD
????????????
Brands: KYB, CHERRY, OOZX, TAIHO, MK, 555, DAIDO, NPW, FORD, MAZDA, KIA.
Address : 62, Race Course Road, Singapore 218568
Telephone Number: (65) 62963915
Fascimile Number: (65) 62966306
Representatives: GEORGE LEE CHIN HON

Bankers: FEB, CKB.
Core Business: Importers & Exporters of all kinds of Japanese Vehicles & Trucks Spareparts.
Company Name : FONG YAT MOTOR CO PTE LTD
??????????
Brands: MAZDA, FORD, KIA
Address : 3, Kallang Way 2A, Fong Tat Building, Singapore 347493
Telephone Number: (65) 67420368, 67426832, 62935722,
Fascimile Number: (65) 67420386, 62942251
Representatives: TAN SEONG KOK

Contact Name: CHEW KOK HUA

URL: http://www.fongtat.com
Core Business: Authorise Stockist for MAZDA, FORD, KIA genuine spare parts, OEM parts. Importer & Exporter.
Company Name : GFA (SINGAPORE) PTE LTD
????
Brands: MAZDA, TOYOTA, NISSAN, SUZUKI, SUBARU, HINO, VOLVO, SAAB, DAIHATSU, VW, AUDI.
Address : 60, Kaki Bukit Place , #09-01, Eunos Techpark, Singapore 415979
Telephone Number: (65) 67421998
Fascimile Number: (65) 67491998
Representatives: TAY TECK YONG

Email Address: gfasinSingNet.com.sg
Bankers: UOB
Core Business: Genuine Japanese & European Vehicles Spare Parts.
Company Name : ONG BROTHERS AUTO CO PTE LTD
???????????
Brands: HONDA, MAZDA, 3 BOND .
Address : Jalan Ampas, #02-02, Ho Seng Lee Flatted Warehouse, Singapore 329513
Telephone Number: (65) 62518786, 62516608
Fascimile Number: (65) 62510810
Representatives: ONG SWEE HUAT

Contact Name: ONG SWEE CHEONG

Email Address: ongbros.com.sg
Bankers: UOB, OCBC
Core Business: Honda, Mazda Genuine Parts, 3 Bond Liquid Gasket.
Company Name : SIN GUAN HIN AUTO PARTS CO
???????
Brands: MAZDA, FORD, BMW.
Address : 24, Veerasamy Road, Singapore 207329
Telephone Number: (65) 62930863, 62981222
Fascimile Number: (65) 62967648, 62981472
Representatives: LOW SEE LEONG

Contact Name: LOW SAY LOO

URL: http://home.pacific.net.sg/~sghauto
Email Address: sghautoPacific.net.sg
Bankers: OCBC
Core Business: Imp. & Exp. Mazda, Ford, BMW Genuine Parts.

As long as its not the pirated version of 3M, then should be good

I was charged $70 for�3 pieces. $60 for�5 pieces (�3 pieces for the rear instead of 1 long one).

�

[thumbsup]

�

From some other link in this forum, one of the bro good work for Mazda stock list:

Company Name : CHIN HON MOTOR & TRADING PTE LTD
????????????
Brands: KYB, CHERRY, OOZX, TAIHO, MK, 555, DAIDO, NPW, FORD, MAZDA, KIA.
Address : 62, Race Course Road, Singapore 218568
Telephone Number: (65) 62963915
Fascimile Number: (65) 62966306
Representatives: GEORGE LEE CHIN HON

Bankers: FEB, CKB.
Core Business: Importers & Exporters of all kinds�of Japanese Vehicles & Trucks Spareparts.
Company Name : FONG YAT MOTOR CO PTE LTD
??????????
Brands: MAZDA, FORD, KIA
Address : 3, Kallang Way 2A, Fong Tat Building, Singapore 347493
Telephone Number: (65) 67420368, 67426832, 62935722,
Fascimile Number: (65) 67420386, 62942251
Representatives: TAN SEONG KOK

Contact Name: CHEW KOK HUA

URL: http://www.fongtat.com
Core Business: Authorise Stockist for MAZDA, FORD, KIA genuine spare parts, OEM parts. Importer & Exporter.
Company Name : GFA (SINGAPORE) PTE LTD
????
Brands: MAZDA, TOYOTA, NISSAN, SUZUKI, SUBARU, HINO, VOLVO, SAAB, DAIHATSU, VW, AUDI.
Address : 60, Kaki Bukit Place , #09-01, Eunos Techpark, Singapore 415979
Telephone Number: (65) 67421998
Fascimile Number: (65) 67491998
Representatives: TAY TECK YONG

Email Address: gfasinSingNet.com.sg
Bankers: UOB
Core Business: Genuine Japanese & European Vehicles Spare Parts.
Company Name : ONG BROTHERS AUTO CO PTE LTD
???????????
Brands: HONDA, MAZDA, 3 BOND .
Address : Jalan Ampas, #02-02, Ho Seng Lee Flatted Warehouse, Singapore 329513
Telephone Number: (65) 62518786, 62516608
Fascimile Number: (65) 62510810
Representatives: ONG SWEE HUAT

Contact Name: ONG SWEE CHEONG

Email Address: ongbros.com.sg
Bankers: UOB, OCBC
Core Business: Honda, Mazda Genuine Parts, 3 Bond Liquid Gasket.
Company Name : SIN GUAN HIN AUTO PARTS CO
???????
Brands: MAZDA, FORD, BMW.
Address : 24, Veerasamy Road, Singapore 207329
Telephone Number: (65) 62930863, 62981222
Fascimile Number: (65) 62967648, 62981472
Representatives: LOW SEE LEONG

Contact Name: LOW SAY LOO

URL: http://home.pacific.net.sg/~sghauto
Email Address: sghautoPacific.net.sg
Bankers: OCBC
Core Business: Imp. & Exp. Mazda, Ford, BMW Genuine Parts.

�

As long as its not the pirated version of 3M, then should be good

�

�

Original 3M at that price?

�
Original 3M at that price?

Not 3M mat at that price. Nope not all parts are 3M only heel plate is 3M. They carry material from China, Korea and Malaysia. My previous ride uses a Malaysia mat with 3M heel plate($100) lasted me for 5.5 yrs and still in good condition..

�
Original 3M at that price?

Thanks. But I realize something weird, the M3 GPS seems to have INS, cos my GPS location is moving in blank map space when I'm in MCE and the GPS location also turned when I turned... but when I exited the tunnel, the position is slightly off from actual location. Do you notice the same thing?

I going to try again tmr...

�

I tried again today and the GPS location really is moving at the correct location inside MCE, where there is no GPS signal. When I exit and join ECP, the GPS location also joined the same ECP location... it is either:

�

1) M3 has Inertial Navigation Sys built in (unlikely, as such system is not cheap)

�

2) There is MCE map in the GPS, but some how its not displayed, but the GPS switched to prediction mode following the hidden MCE tunnel in the map. (more likely, as normal TOMTOM GPS map already have MCE in their map and M3 uses TOMTOM)

Edited by Brainstorm, 06 January 2015 - 08:56 PM.

Knocking sound from suspension when going pass speed bump. It happened before my 1k servicing and I told the person who served me when I went for 1k servicing. All he told me was monitor first. If I go back for 5k servicing, and they still tell me the same "monitor" first bulls**t, I'm gonna make a fuss. So obvious, the sound so loud, whats there to monitor?

�

They are trying to smoke customer. Think we first time own and drive car?

�

Edited by Oppositelock, 06 January 2015 - 11:15 PM.

Knocking sound from suspension when going pass speed bump. It happened before my 1k servicing and I told the person who served me when I went for 1k servicing. All he told me was monitor first. If I go back for 5k servicing, and they still tell me the same "monitor" first bulls**t, I'm gonna make a fuss. So obvious, the sound so loud, whats there to monitor?

�

They are trying to smoke customer. Think we first time own and drive car?

�

�

Hi, I'm not driving a M3 but generally if the car is in warranty (moreover from AD), car owner don't have to wait until next servicing. Try raise the issue/complain again to ask them to check. I think for safety first. cheers� ^_^

my iSTOP has never stop for more than 30seconds. does it really save that much petrol if my engine switch off for that few seconds? does anyone here iSTOP will stop throughout the traffic light time until u release the brakes?

my iSTOP has never stop for more than 30seconds. does it really save that much petrol if my engine switch off for that few seconds? does anyone here iSTOP will stop throughout the traffic light time until u release the brakes?

�

How long it stop depends on how fully charged is the capacitor. But, bear in mind that capacitor is not like battery as it charges & discharges quite quickly, which is good for city driving. I think savings would be over time, probably btw 4 to 7%, you can check it out with the Fuel Economy Monitor.

my iSTOP has never stop for more than 30seconds. does it really save that much petrol if my engine switch off for that few seconds? does anyone here iSTOP will stop throughout the traffic light time until u release the brakes?

Try turning off the A/C compressor,leave the blower on..can lasts up to 2 mins.

my iSTOP has never stop for more than 30seconds. does it really save that much petrol if my engine switch off for that few seconds? does anyone here iSTOP will stop throughout the traffic light time until u release the brakes?

Mine sometimes can stop throughout, especially at night. What aircon temperature did u set? If set too low, the istop will start the engine very fast. You can go to the Fuel management monitor page and the iEloop page to see what is the cause of the short stop. There are 3 icons there to show engine, battery and aircon. If the icon is not glowing, that means that item is the cause.

Knocking sound from suspension when going pass speed bump. It happened before my 1k servicing and I told the person who served me when I went for 1k servicing. All he told me was monitor first. If I go back for 5k servicing, and they still tell me the same "monitor" first bulls**t, I'm gonna make a fuss. So obvious, the sound so loud, whats there to monitor?
�
They are trying to smoke customer. Think we first time own and drive car?

You took the video clip when raining? I can only hear the rain noise.. ha

You took the video clip when raining? I can only hear the rain noise.. ha

�

Ya, try listen carefully at the 2 sec mark. Its the knocking sound. Today when i was exiting Lido's carpark also got sound whenever i pass through a speed bump. Annoying. To be honest, I won't recommend this car to a friend. Such simple things also can cock up. Genius.�

My iStop will start up the engine like after 10-15s the most. Aircon temp is set at 22/20. But when te engine start up again. On the fuel Ecconomy page. The next few seconds. They asked me to put to neutral to activate which I donno for what.

My car do have the nock nock sound. It's not on all types of bumps that will have. Only those super high like in JB kind. I heard the nock sound. There's just that one nock. It doesn't go nock nock nock.

My iStop will start up the engine like after 10-15s the most. Aircon temp is set at 22/20. But when te engine start up again. On the fuel Ecconomy page. The next few seconds. They asked me to put to neutral to activate which I donno for what.

My car do have the nock nock sound. It's not on all types of bumps that will have. Only those super high like in JB kind. I heard the nock sound. There's just that one nock. It doesn't go nock nock nock.

Your aircon temp is set too low... mine is at 25deg only...

All cars when going over bumps will have some damping noise as the shock absobers are working. Need to differentiate from the nock nock sound.

Your aircon temp is set too low... mine is at 25deg only...

All cars when going over bumps will have some damping noise as the shock absobers are working. Need to differentiate from the nock nock sound.

�

it sound�exactly like the nock nock�sound one of us posted in the video. but not all speed bumps willl have. i only encounter twice at the same bump in jb yesterday cos no carpark lot so made 2 turns and went across the bump twice. but it doesnt go nock nock nock. it only has 1 nock sound. still at my 500km only.

�

does our m3 have this function to search for car? like press the button on the alarm and the car horn goes on? anybody knows?

Edited by funkykiddo, 08 January 2015 - 05:35 PM.

Hi bro,
�
The Dok Dok sound is still there, more like faint jiggling noise when turning at low speed or travelling at slow speed at grated roads. Most prominent when there is a sudden up slope.
I should be going back there in about 2 weeks time when my mileage reaches 5000km.
I will give leng kee one more chance if not I will go back to UBI.
Don't think it is that serious. It might be due to the lack of lubrication of the top mount bearing.
It was rather similar to my previous ride�on�coilovers�which was using a pillow mount ( and metal top hat), which sounded more awfully when�they got shot. �I am rather surprised Mz3 comes with rubber top hats with metal bearing as well.
Please see the link here for more info.
http://mazda3revolut...future-tsb.html

Scenario: knock sound before up a hump and a knock sound when down a hump.
To follow up with my knock knock sound repair: first repair was to replace arm bushing and top mount damper/rubber at Ubi. A soft knock knock sound remain . ( confirm with the same tester today) Today they did a insulate FRT COIL SPRING as written in my tax invoice. So far going thru a few hump, it had been good. Will update again in 2 week time.

My iStop will start up the engine like after 10-15s the most. Aircon temp is set at 22/20. But when te engine start up again. On the fuel Ecconomy page. The next few seconds. They asked me to put to neutral to activate which I donno for what.

My car do have the nock nock sound. It's not on all types of bumps that will have. Only those super high like in JB kind. I heard the nock sound. There's just that one nock. It doesn't go nock nock nock.

I stop is design to save fuel accumulative on long term. If the temp is set too low, cabin temp will try to be met at all times, resulted I stop being cut off. If the cabin temp is set to lowest and blower to full I stop will not work. As for myself, my temp is set at 26degree and I stop can last 2 min when it's fully charged. I do notice I stop dun work that long during a warm day..

Scenario: knock sound before up a hump and a knock sound when down a hump.
To follow up with my knock knock sound repair: first repair was to replace arm bushing and top mount damper/rubber at Ubi. A soft knock knock sound remain . ( confirm with the same tester today) Today they did a insulate FRT COIL SPRING as written in my tax invoice. So far going thru a few hump, it had been good. Will update again in 2 week time.

Thanks for updating us bro.Done at Ubi?
I should be going to lengkee one next week.
I am still hearing the jingles on those uneven roads.

Edited by Dalenico, 08 January 2015 - 07:37 PM.

Thanks for updating us bro.Done at Ubi?
I should be going to lengkee one next week.
I am still hearing the jingles on those uneven roads.

Yes I did it at Ubi . So far not much sound heard. Keeping my finger cross..

�

Ya, try listen carefully at the 2 sec mark. Its the knocking sound. Today when i was exiting Lido's carpark also got sound whenever i pass through a speed bump. Annoying. To be honest, I won't recommend this car to a friend. Such simple things also can cock up. Genius.�

�

Agreed...i would not recommend this car to anyone because i am starting to see more on the road....becoming a common sight� [:p]

�

I am glad the main problem encounter by most drivers is the sound they hear when going over hump and not a flashing "D", problematic throttle body, killer airbags, etc. �At least our problem can be solved easily by replacing some bushings. �I guess it did not bother me much because I have my favourite music on most of the time when I drive over humps and I do not have the habit of turning the volume down before i going over a hump.

�

Anyway, I doubt i could hear it anymore even if i try because Eurokas has replaced the bushings during my recent service appointment ...FOC� [thumbsup]

�
Agreed...i would not recommend this car to anyone because i am starting to see more on the road....becoming a common sight�
�
I am glad the main problem encounter by most drivers is the sound they hear when going over hump and not a flashing "D", problematic throttle body, killer airbags, etc. �At least our problem can be solved easily by replacing some bushings. �I guess it did not bother me much because I have my favourite music on most of the time when I drive over humps and I do not have the habit of turning the volume down before i going over a hump.
�
Anyway, I doubt i could hear it anymore even if i try because Eurokas has replaced the bushings during my recent service appointment ...FOC�

Given that there are so many technologies advances that are built into M3 compared to other car makes, like high compression 14:1 engine on normal octane fuel, new generation powerful transmission, high rigidity but light body, increased torque in low-mid rpm, excellent fuel efficiency, advance i-Stop, brake regenerative power i-Eloop, etc.. I think a nock sound, though tarnish the M3 perfect image, it shld not be blown out of proportion and overshine all these advantages. (Lucky my M3 don't have nock sound)

Edited by Brainstorm, 08 January 2015 - 10:52 PM.

From some other link in this forum, one of the bro good work for Mazda stock list:

Company Name : CHIN HON MOTOR & TRADING PTE LTD
????????????
Brands: KYB, CHERRY, OOZX, TAIHO, MK, 555, DAIDO, NPW, FORD, MAZDA, KIA.
Address : 62, Race Course Road, Singapore 218568
Telephone Number: (65) 62963915
Fascimile Number: (65) 62966306
Representatives: GEORGE LEE CHIN HON

Bankers: FEB, CKB.
Core Business: Importers & Exporters of all kinds of Japanese Vehicles & Trucks Spareparts.
Company Name : FONG YAT MOTOR CO PTE LTD
??????????
Brands: MAZDA, FORD, KIA
Address : 3, Kallang Way 2A, Fong Tat Building, Singapore 347493
Telephone Number: (65) 67420368, 67426832, 62935722,
Fascimile Number: (65) 67420386, 62942251
Representatives: TAN SEONG KOK

Contact Name: CHEW KOK HUA

URL: http://www.fongtat.com
Core Business: Authorise Stockist for MAZDA, FORD, KIA genuine spare parts, OEM parts. Importer & Exporter.
Company Name : GFA (SINGAPORE) PTE LTD
????
Brands: MAZDA, TOYOTA, NISSAN, SUZUKI, SUBARU, HINO, VOLVO, SAAB, DAIHATSU, VW, AUDI.
Address : 60, Kaki Bukit Place , #09-01, Eunos Techpark, Singapore 415979
Telephone Number: (65) 67421998
Fascimile Number: (65) 67491998
Representatives: TAY TECK YONG

Email Address: gfasinSingNet.com.sg
Bankers: UOB
Core Business: Genuine Japanese & European Vehicles Spare Parts.
Company Name : ONG BROTHERS AUTO CO PTE LTD
???????????
Brands: HONDA, MAZDA, 3 BOND .
Address : Jalan Ampas, #02-02, Ho Seng Lee Flatted Warehouse, Singapore 329513
Telephone Number: (65) 62518786, 62516608
Fascimile Number: (65) 62510810
Representatives: ONG SWEE HUAT

Contact Name: ONG SWEE CHEONG

Email Address: ongbros.com.sg
Bankers: UOB, OCBC
Core Business: Honda, Mazda Genuine Parts, 3 Bond Liquid Gasket.
Company Name : SIN GUAN HIN AUTO PARTS CO
???????
Brands: MAZDA, FORD, BMW.
Address : 24, Veerasamy Road, Singapore 207329
Telephone Number: (65) 62930863, 62981222
Fascimile Number: (65) 62967648, 62981472
Representatives: LOW SEE LEONG

Contact Name: LOW SAY LOO

URL: http://home.pacific.net.sg/~sghauto
Email Address: sghautoPacific.net.sg
Bankers: OCBC
Core Business: Imp. & Exp. Mazda, Ford, BMW Genuine Parts.

Thanks!!

�

Agreed...i would not recommend this car to anyone because i am starting to see more on the road....becoming a common sight�

�

I am glad the main problem encounter by most drivers is the sound they hear when going over hump and not a flashing "D", problematic throttle body, killer airbags, etc. �At least our problem can be solved easily by replacing some bushings. �I guess it did not bother me much because I have my favourite music on most of the time when I drive over humps and I do not have the habit of turning the volume down before i going over a hump.

�

Anyway, I doubt i could hear it anymore even if i try because Eurokas has replaced the bushings during my recent service appointment ...FOC�

�

Common is good, more spare parts. In future no need die die go back AD. Btw, killer airbag is not car manufacturer fault. The fault lies with Takata.�

�

Imagine a car so new yet the sound is so obvious and can capture it so clearly on iphone already. Ever wonder how loud and often will it be when the car is 3 years old? Today i captured another video, this time without rain. Will share over the weekends when I got more time to upload.�

�

How long does they take to replace the brushing? I'm going to ask them to get it fix during my 5k service. And of course must be FOC, if not what is the warranty for?�

[quote name="Oppositelock" post="5383494" timestamp="1420732289"]

�
Common is good, more spare parts. In future no need die die go back AD. Btw, killer airbag is not car manufacturer fault. The fault lies with Takata.�
�
Imagine a car so new yet the sound is so obvious and can capture it so clearly on iphone already. Ever wonder how loud and often will it be when the car is 3 years old? Today i captured another video, this time without rain. Will share over the weekends when I got more time to upload.�
�
How long does they take to replace the brushing? I'm going to ask them to get it fix during my 5k service. And of course must be FOC, if not what is the warranty for?�[/quot

For mine, both occasions took the whole day. Drop the car at 9am and collect at 5 pm.

�

I tried again today and the GPS location really is moving at the correct location inside MCE, where there is no GPS signal. When I exit and join ECP, the GPS location also joined the same ECP location... it is either:

�

1) M3 has Inertial Navigation Sys built in (unlikely, as such system is not cheap)

�

2) There is MCE map in the GPS, but some how its not displayed, but the GPS switched to prediction mode following the hidden MCE tunnel in the map. (more likely, as normal TOMTOM GPS map already have MCE in their map and M3 uses TOMTOM)

�

Tried a few more days using GPS thru MCE, it seems like there is some kind of INS (Inertial Navigation System) buit into M3. Because sometimes when I exited the MCE, the GPS position is slightly off the actual position, sometimes its almost on the same location when it reacquired the GPS signal. [drivingcar]

�

Anyway there is another update of Southeast Asia maps when I log in to Mazda Toolbox this morning, updating now and will check it out on Mon if the MCE is included in this update. ��

�

Tried a few more days using GPS thru MCE, it seems like there is some kind of INS (Inertial Navigation System) buit into M3. Because sometimes when I exited the MCE, the GPS position is slightly off the actual position, sometimes its almost on the same location when it reacquired the GPS signal.

�

Anyway there is another update of Southeast Asia maps when I log in to Mazda Toolbox this morning, updating now and will check it out on Mon if the MCE is included in this update. ��

�

Just tried using the GPS simulation mode and there is MCE in the latest map update.� [thumbsup]

�

Mazda Toolbox

Bros can I get Mazda to update the infortainment sys for me? I going for the 5k servicing liao

And did any of the bros install the dvr cam with Mazda?

Any Bros recently been to Mazda to see if they brought in more accessories (led skid plate for doors, body kit) for mazda3?

Thanks alot

Bros can I get Mazda to update the infortainment sys for me? I going for the 5k servicing liao

And did any of the bros install the dvr cam with Mazda?

Any Bros recently been to Mazda to see if they brought in more accessories (led skid plate for doors, body kit) for mazda3?

Thanks alot

Just had Mazda update my infortainment to v33. But i dont thk they updated the map as im still undergrd when driving on MCE.

Just had Mazda update my infortainment to v33. But i dont thk they updated the map as im still undergrd when driving on MCE.

�

Any improvement for v33? Think mine is still v31. Thks.�

�
Any improvement for v33? Think mine is still v31. Thks.�

How to find out which version is mine install?

How to find out which version is mine install?

�

It can be found under Infotainment page > Settings > System > About

�
Any improvement for v33? Think mine is still v31. Thks.�

Not too sure if there is any improvement, but reason why they upgraded was that I had experienced a static screen on the morning before my 10K Svc. So far seems fine. Just updated my map, so try tml morning.

Not too sure if there is any improvement, but reason why they upgraded was that I had experienced a static screen on the morning before my 10K Svc. So far seems fine. Just updated my map, so try tml morning.

�

I just tried this morning, GPS directed me to MCE. [drivingcar] � [thumbsup] ��

�
It can be found under Infotainment page > Settings > System > About

Thanks bro.

Read that for the Sky AT, instead of only relying on the torque converter, it has clutch plates.
In transmitting the power, the clutch plates plays a primary role while the TC plays a secondary role.

Anyone bro here who previously driven a 6AT car like Elantra can comment on the 2 respective GB(s).? �TIA.

Read that for the Sky AT, instead of only relying on the torque converter, it has clutch plates.
In transmitting the power, the clutch plates plays a primary role while the TC plays a secondary role.

Anyone bro here who previously driven a 6AT car like Elantra can comment on the 2 respective GB(s).? �TIA.

Every A/T got clutch plates,it is only Mazda Skyactiv A/T "Lock-up" very fast,so that you got a direct feel,almost like DSG,but the down side is a bit more jerky....Elantra gearbox is the same as Kia K3,it is smooth,but not so fast shifting....Mazda gearbox also upshift in very low rpm to save fuel.

Edited by ER-3682, 13 January 2015 - 07:38 PM.

�

I just tried this morning, GPS directed me to MCE. � ��

�

nice! stupid qns bros..where is the sd card for the system?

�

nice! stupid qns bros..where is the sd card for the system?

bro, open up your centre arm rest...

Every A/T got clutch plates,it is only Mazda Skyactiv A/T "Lock-up" very fast,so that you got a direct feel,almost like DSG,but the down side is a bit more jerky....Elantra gearbox is the same as Kia K3,it is smooth,but not so fast shifting....Mazda gearbox also upshift in very low rpm to save fuel.

I test drove both cars on the same day .... and I will tell you how my butt felt day that ....

the more I rev the Mazda 3, the merrier it goes and the engine grew bigger.�

the more I rev the Elantra, the merrier the engine goes too and felt even faster than the Mazda but the engine felt it grew smaller and about to explode with joy and happiness ... and unfortunately, I feel the car fish-tail a bit at medium-hard braking at 100km/hr.

Just what my butt told me.

�

I test drove the K3 as well, smooth revving engine but the 17" wheels kill the fun but my butt told me this car suspension setup might be the best for city driving among the 2 cars here.�

�

nice! stupid qns bros..where is the sd card for the system?

We are all here to learn bro ... keep the qns rolling ...�

Good Morning, thanks VB & ER.

I test drove both cars on the same day .... and I will tell you how my butt felt day that ....

the more I rev the Mazda 3, the merrier it goes and the engine grew bigger.�

the more I rev the Elantra, the merrier the engine goes too and felt even faster than the Mazda but the engine felt it grew smaller and about to explode with joy and happiness ... and unfortunately, I feel the car fish-tail a bit at medium-hard braking at 100km/hr.

Just what my butt told me.

�

I test drove the K3 as well, smooth revving engine but the 17" wheels kill the fun but my butt told me this car suspension setup might be the best for city driving among the 2 cars here.�

We are all here to learn bro ... keep the qns rolling ...�

�

Thks bro!! Valuable feedback as usual [thumbsup]

�

Mz2 coming, lets us know your thoughts if possible.

Believe it will be the hatchback one at this weekend Motorshow and not the sedan so may not be a good comparison with the Mz3. Let's see though, cheers!!

�

Thks bro!! Valuable feedback as usual

�

Mz2 coming, lets us know your thoughts if possible.

Believe it will be the hatchback one at this weekend Motorshow and not the sedan so may not be a good comparison with the Mz3. Let's see though, cheers!!

�

No problem bro.

But my backside not so itchy now as I have my Mazda 3 ,,,�Hahaha ....�

�

Anyway, just send in for 5000km servicing, told them the "nock nock" sound.

A�mech called KOH I �think was assigned to test drive the car with me.

Immediately upon the 1 hump in an open carpark with many humps, "nock nock" was heard.

He suspect it was the lower arm bushing issue as every hump he goes over have this sound.

Sitting at the passenger the sound was very audible.

�

No problem bro.

But my backside not so itchy now as I have my Mazda 3 ,,,�Hahaha ....�

�

Anyway, just send in for 5000km servicing, told them the "nock nock" sound.

A�mech called KOH I �think was assigned to test drive the car with me.

Immediately upon the 1 hump in an open carpark with many humps, "nock nock" was heard.

he suspect it was the lower arm bushing issue as every hump he goes over have this sound.

Sitting at the passenger the sound was very audible.

Need to do wheel alignment if change lower arm bushing?

Need to do wheel alignment if change lower arm bushing?

Everything will be taken care buy Eurokars.. No worry bro.

�
No problem bro.
But my backside not so itchy now as I have my Mazda 3 ,,,�Hahaha ....�
�
Anyway, just send in for 5000km servicing, told them the "nock nock" sound.
A�mech called KOH I �think was assigned to test drive the car with me.
Immediately upon the 1 hump in an open carpark with many humps, "nock nock" was heard.
He suspect it was the lower arm bushing issue as every hump he goes over have this sound.
Sitting at the passenger the sound was very audible.

Mine was fix at Ubi by the name of Mr Koh as well. He is good with this now. He solve mine nock nock sound last week and it has been so far so good.

Mine was fix at Ubi by the name of Mr Koh as well. He is good with this now. He solve mine nock nock sound last week and it has been so far so good.

�

So far so good.

Nock nock sound no more ....�

�

Any improvement for v33? Think mine is still v31. Thks.�

�

I just went for servicing yesterday ... still V31.�

Think need to inform them to update.

Need to do wheel alignment if change lower arm bushing?

�

If you change outside and depending on cars, sometimes might need to do.

My previous FIAT GP most of the time no need after changing lower arm bushing.

Everything will be taken care buy Eurokars.. No worry bro.

Mine was fix at Ubi by the name of Mr Koh as well. He is good with this now. He solve mine nock nock sound last week and it has been so far so good.

Just sent to Leng Kee though my mileage is still short of 5000km.

The Mechanic test drove with me and managed to hear the noise again.

Was informed by them that every production batch gives different sound..cos mazda Japan modified it but it created another new sound every time to do so. So it is batch specific...

Shall update again...

Just done my 1k servicing. Also changed lower arm bushing left and right.

According to them, no need to do wheel alignment for changing lower arm bushing.

Also asked them to update my ver 31 to 33. Thanks to all bros discussion here,

so I know what to request for my 1K servicing. [wave] � [thumbsup]

To all who wants to update to V33.�

�

I just updated mine after complaining that my Infortainment gets hang twice after my 5K service to 10K service.�

They mentioned that V33 just came out and updated mine to V33.

�

After came out from workshop, i realized that if you used to listen to MP3 thru USB and with shuffle mode on. This feature will be disable every time you off and start your engine / module. so you need to enable the shuffle mode ever time you on your engine, otherwise, the MP3 will just running as sequence as per the file.�

�

So far the rest of the thing are the same. not realized anything changes for this update.�

The update doesnt affect the map version regardless of new or old.�

�

Mine is old version and cannot be update anymore (MCE is not in the database)

�

I will feedback again if i found anything different for the newer version.

�

Another update.�

�

For those who going to 20K servicing, the charges will be S$382 exclude GST subject to change.�

�

They only change E/O , A/C Filter , Oil Filter only + Tighten of some parts. The rest of the thing are fall into "Inspection"�

�

I also changed the bushing after complaining about the abnormal sound from my absorber (Front) but i will monitor again. My previous problem was, after heavy rain, the abnormal sound will be occur only over a hump. Normal dry road over hump has no problem.�

These few days no rain, so i cant confirm is the problem resolve or not. Anyway, after changing it, everything is like normal as unchanged like that. hope they really resolve this problem to me.�

�

Hi everyone, first post here but have been reading really useful information in this thread..

Was wondering where do some bros get their accessories from when they say mazda usa oem website.. Anyone able to share some links? Thanks:)

Today, I�drove in�to Ubi Service centre�and looked for Koh to feedback on the "NOCK NOCK" when over a hump and "TICK TICK" on left front panel while cruising uneven road.

�

They changed the lower arm bush and insulate the coil spring for the (left and right). So far...ok.

�

But the "tick tick" sound still persist (though the noise is "faint"�after they lubricate and adjust panel)

�

Will monitor and update again!

�

Just done my 1k servicing. Also changed lower arm bushing left and right.

According to them, no need to do wheel alignment for changing lower arm bushing.

Also asked them to update my ver 31 to 33. Thanks to all bros discussion here,

so I know what to request for my 1K servicing. �

�

Edited by Kiddies, 15 January 2015 - 06:05 PM.

�

Mine is old version and cannot be update anymore (MCE is not in the database)

�

�

Strange that you wrote "old version and cannot be update anymore" considering you only have 20,000KM on your car.� I thought you have three years of free update?

�

https://mazda-na.nav...ortal/downloads

�

Did you try to update the map yourself?� There is an update available that has just been released.

�

Download the TOOLBOX and install it on your PC (not Mac), connect your SD Card to your PC and simply follow the on screen instruction.

You may refer to below for the Mazda US website. Can refer to Taobao for more.... [thumbsup]

http://accessories.m...4 MAZDA3 4-Door

�

yes. Send to a�warehouse in US�(local agent)�and�ship to Singapore. Bought it on impulse.

�

Alternatively, I discovered Amazon also have a few (NOT ALL)�of the items; Free shipping & Delivery to S,pore�if you order >=US$125

�

I got most of the interior and exterior items via taobao: -

http://detail.tmall....?id=41865931591�(Most damage from this dealer; gd service; �they also�throw in freebies.

http://detail.tmall....?id=39682528836�(Avg service, but price quite competitive.)

http://item.taobao.c..._u=526p8ig221dc. (Ordered from them, but they could not ship to Singapore; need a third party to ship to Singapore.

�

�

�

Anyone booking their new mazda 3 recently or planning to book one?

Another update.�

�

For those who going to 20K servicing, the charges will be S$382 exclude GST subject to change.�

�

They only change E/O , A/C Filter , Oil Filter only + Tighten of some parts. The rest of the thing are fall into "Inspection"�

�

I also changed the bushing after complaining about the abnormal sound from my absorber (Front) but i will monitor again. My previous problem was, after heavy rain, the abnormal sound will be occur only over a hump. Normal dry road over hump has no problem.�

These few days no rain, so i cant confirm is the problem resolve or not. Anyway, after changing it, everything is like normal as unchanged like that. hope they really resolve this problem to me.�

�

Do you have a breakdown for S$ 382? ie how much is EO, A/C Filter, Oil Filter, labour? Thanks.

You may refer to below for the Mazda US website. Can refer to Taobao for more....
[url="http://accessories.m...4 MAZDA3 4-Door[/ur

�
�
�

If your looking for Mazda speed stuff this are a few link
Thru vpost usa -
http://mazdagear.com...---mazda-3.aspx
http://mazdapartspeo...- Front Air Dam

Ebay
http://m.ebay.com/itm/301262752018

Just sent to Leng Kee though my mileage is still short of 5000km.

The Mechanic test drove with me and managed to hear the noise again.

Was informed by them that every production batch gives different sound..cos mazda Japan modified it but it created another new sound every time to do so. So it is batch specific...

Shall update again...

Changed the lower arm bushing for the 2nd time and the Strut mount with the bearing.

Well, after driving for some time, I still can hear the faint jingling sound on rough roads.

Probably, the spring are on the stiffer side and that is why the sound is inevitable.

Perhaps, insulation of spring will really work

Hi Bro, no breakdown list.

�

the list that given to me is those list and price on the service like...

20K is $382, 30K is two hundred plus, then 40K is four hundred plus. up to 120K like that.

But about 100K , this is the most expensive one which is about a thousand plus like that.

�

i try to upload later when i back to office.

�

�

Do you have a breakdown for S$ 382? ie how much is EO, A/C Filter, Oil Filter, labour? Thanks.

�

Hi Bro, no breakdown list.

�

the list that given to me is those list and price on the service like...

20K is $382, 30K is two hundred plus, then 40K is four hundred plus. up to 120K like that.

But about 100K , this is the most expensive one which is about a thousand plus like that.

�

i try to upload later when i back to office.

�

That'll be great. Thanks!

Any one using Saris Bones 2 or 3 on your 5-door hatch?

Main concern is the straps over the spoiler...and when fully loaded would the straps damage it?

Today I change out the front pair of stock speakers to my Hertz speakers
Salvage from my old car before scrap. Do it in JB. Labour for taking out and installing = RM 60.

I thk shld black out. Better check bro.

I too found out something today. Never had to use the 12V outlet, and when I tried to plug a car vacuum last night... Didn't work. I thought the vacuum was faulty since car new rite..changed another unit and still dead. Just had 10k Svc.. So will be quite long time til next round.

�

The 12V outlet shd work when car is running or when the battery power is on. If not, then maybe shd get it checked.

Hi all,

�

Need some advice from the gurus here.

�

Been driving my new Madza 3 for about 2 weeks.�1k servicing soon to come. In the past 2 days, I noticed that the digital odometer�display (at the bottom left portion of the driver console) still shows the distance (still�dimly lit�up)�even I turned off the engine. I think by right everything should be blacked out when I switch off the engine? I wonder is this normal or something is wrong with the display.

�

Any bros can advise?

Normal,together with the alarm LED,these used very little energy,no worries..

I thk shld black out. Better check bro.

I too found out something today. Never had to use the 12V outlet, and when I tried to plug a car vacuum last night... Didn't work. I thought the vacuum was faulty since car new rite..changed another unit and still dead. Just had 10k Svc.. So will be quite long time til next round.

�

Check the vacuum plug length, is it short? The 12V outlet on our M3 is deeper than normal. My Griffin USB charger also cannot work on M3 as the charger is too short. Changed to a longer length USB charger and it works. � [sweatdrop]

�

Edited by Brainstorm, 19 January 2015 - 08:44 PM.

�
Check the vacuum plug length, is it short? The 12V outlet on our M3 is deeper than normal. My Griffin USB charger also cannot work on M3 as the charger is too short. Changed to a longer length USB charger and it works. �
�

Thanks, I tried with various plugs after tt but non worked..:(

Thanks, I tried with various plugs after tt but non worked..:(

might just be the fuse..

Hi,
Did anyone change their Mazda 3 tyres/rims from 16" to 17" ?
Where to go to get 17" Rims with Mazda logo ?
Thanks.

Hi,
Did anyone change their Mazda 3 tyres/rims from 16" to 17" ?
Where to go to get 17" Rims with Mazda logo ?
Thanks.

Traded in my Mz original 16 x 6.5jj rim to 16 x 7jj rim.
Can't get back the Mz logo cap because the boss need them to sell my Mz rim off as a set.
Me change 16" to 16" is because I wanna use back my original tire. Also rim offset from original +50 to
aftermarket rim +38. Now whole setup looks better. Doesn't have the sunken rim/tire look anymore. If you know what I mean.

Hi,
Did anyone change their Mazda 3 tyres/rims from 16" to 17" ?
Where to go to get 17" Rims with Mazda logo ?
Thanks.

�

changed mine to 17 inch but cant used back the mazda logo cos too small

changed mine to 17 inch but cant used back the mazda logo cos too small

Thanks. Yours is the 2014 Mazda3 1.5L?
What are good rim brands? Where can i preview the designs online? Which shop is trustworthy/honest ? Sorry am a noobie on this. What size tyres did you fit? Was there significant reduction in pickup of the car? Thanks.

�

changed mine to 17 inch but cant used back the mazda logo cos too small

brother, show picture leh� [nod]

Traded in my Mz original 16 x 6.5jj rim to 16 x 7jj rim.
Can't get back the Mz logo cap because the boss need them to sell my Mz rim off as a set.
Me change 16" to 16" is because I wanna use back my original tire. Also rim offset from original +50 to
aftermarket rim +38. Now whole setup looks better. Doesn't have the sunken rim/tire look anymore. If you know what I mean.

�

Yar .... hehehe ...

anyway, the original toyo tires I find very noisy for its performance but they are quite good.

Further to what i reported for 5k servicing that a Mr. Koh from UBI had changed the front right strut bushing and isolate the spring, all has been well. On the hindsight, the small little creaking sounds in the cabin is more obvious.

�

After driving it for a while, I found that the car is less fidgety (like the steering is trying to fight your input and gets easily agitated) on high speed on the highway and the usual corners were made made easier to take with confidence.

�

I urge all those who had the "TOCK TOCK" sound to rectify the issue and feel what the designer had originally intend the car to handle.

might just be the fuse..

�

i bought from courts.. the brand is called innergie i think

brother, show picture leh�

�

Yar .... hehehe ...

anyway, the original toyo tires I find very noisy for its performance but they are quite good.

�

Gunmetal :)

�

Thanks. Yours is the 2014 Mazda3 1.5L?
What are good rim brands? Where can i preview the designs online? Which shop is trustworthy/honest ? Sorry am a noobie on this. What size tyres did you fit? Was there significant reduction in pickup of the car? Thanks.

�

yup ..erm i just got from autobacs forged rims.. no particular brand

�

tyres need to be correct size if no odometer reading will b off

�

pick up still gd

Edited by Statr22, 21 January 2015 - 08:46 PM.

�

i bought from courts.. the brand is called innergie i think

�

Gunmetal :)

�

�

�

yup ..erm i just got from autobacs forged rims.. no particular brand

�

tyres need to be correct size if no odometer reading will b off

�

www.mostwheels.com 2014-8-21 23 32 27.png

�

pick up still gd

bro, really fuse problem? it happened to my old car before on a sunday..went to autobaccs and got 3 for 2 dollars

Does anyone know whether there is an additional AV input for the MZD system ?�

Thanks. Yours is the 2014 Mazda3 1.5L?
What are good rim brands? Where can i preview the designs online? Which shop is trustworthy/honest ? Sorry am a noobie on this. What size tyres did you fit? Was there significant reduction in pickup of the car? Thanks.

Hi bro. There are many rims to choose and also depends on your budget. If u wish, u can try Cheng an da. They sell RM rims, made in Taiwan and has many selection for u to choose. Goggle them or u can find them in FB.

Does anyone know whether there is an additional AV input for the MZD system ?�

download the service manual bro.

easily available within this thread or just google.

�

yup ..erm i just got from autobacs forged rims.. no particular brand

�

tyres need to be correct size if no odometer reading will b off

�

www.mostwheels.com 2014-8-21 23 32 27.png

�

pick up still gd

�

Show the pic of the whole car laaaaaa ....� [grin]

Hi Mazda 3 1.5 owners

�

What's your fuel consumption and RPM when at highway speeds (90-110kmph)?

�

Thanks.

Hi Mazda 3 1.5 owners

�

What's your fuel consumption and RPM when at highway speeds (90-110kmph)?

�

Thanks.

depends on distance travel ... can hit 5l/100km or less if cruising without stopping at constant speed for > 30km.

RPM should be about 2000rpm i think at 6th gear.

[thumbsup] �Yup, I experienced that too when I travelled from Woodlands to Changi via BKE/TPE at 90-100kmh.

�

depends on distance travel ... can hit 5l/100km or less if cruising without stopping at constant speed for > 30km.

RPM should be about 2000rpm i think at 6th gear.

�

Edited by ST69, 22 January 2015 - 03:03 PM.

Did anyone upgrade a amp for the radio music and what is the brand and price?

Bring driving for the past 3 months, so far can achieve FC of�5.5�-6.1L/100km (Avg) per full tank.

�

I observed RPM of approx. 2.2K - 2.5K�while cruising between� 90km�- 130km.

�

Hi Mazda 3 1.5 owners

�

What's your fuel consumption and RPM when at highway speeds (90-110kmph)?

�

Thanks.

�

Does anyone know any local car audio shop who has installed such device (see link) or sells such device ?

�

http://car-solutions...rom-2014-my.php

Hi Mazda 3 1.5 owners
�
What's your fuel consumption and RPM when at highway speeds (90-110kmph)?
�
Thanks.

2,000rpm gives you 88Kmph with comsumption of 4.x L/100Km at level ground.

Today I change out the front pair of stock speakers to my Hertz speakers
Salvage from my old car before scrap. Do it in JB. Labour for taking out and installing = RM 60.

Người đăng: googlebest vào lúc 11:59
Gửi email bài đăng này BlogThis!Chia sẻ lên X Chia sẻ lên Facebook Chia sẻ lên Pinterest

mycarforum

Chủ Nhật, 27 tháng 11, 2016

2014 Mazda 3 part 20

Không có nhận xét nào:

Đăng nhận xét