The cable for 5 V camera...Can make what???
The cable for 5 V camera...
There are two options there. Which one u referring???
The adapter...easier....thks!There are two options there. Which one u referring???
The adapter...easier....thks!
When u need it??? Have to go down to Sim Lim Tower to buy the adapters. Unless u can pass me the adapters and I do the soldering job.
The adapter...easier....thks!
That option, just go and buy, connect wires, done in 5mins. Not rocket science.
I already did mine.
Not in a hurry......take ur time ....if ok I come over and collect...thks!When u need it??? Have to go down to Sim Lim Tower to buy the adapters. Unless u can pass me the adapters and I do the soldering job.
Not in a hurry......take ur time ....if ok I come over and collect...thks!
Ok. Then will do it during the weekend. See when I free, pop down to sim lim tower n get the adapters. Should be able to collect it during this weekend. Will PM u when its ready.
I dun have soldering ....u expert sure say ok...That option, just go and buy, connect wires, done in 5mins. Not rocket science.
I already did mine.
Wow ...thats great...thks bro....makan on me...Ok. Then will do it during the weekend. See when I free, pop down to sim lim tower n get the adapters. Should be able to collect it during this weekend. Will PM u when its ready.
I dun have soldering ....u expert sure say ok...
Boh leh, I paisay trouble him lah.
No dont misunderstand bro, I thought it would be better to pm u because i m afraid u might missed out the qns in this fast moving thread because u guys are busy at IT show, dont anyhow think lei!Yes you can switch on motion in the menu , and once its detected it will save 1 min clip .
If you still have any questions dont hesitate to contact us 65706448
chill ah shochong , also many people asking about your products here no one complaint mah
Edited by Shochong, 11 June 2012 - 11:15 AM.
bro where u buy, i also want!Boh leh, I paisay trouble him lah.
bro where u buy, i also want!
Sim Lim Tower lor.
possible to tell me the exact shop and item name? wan to just grab n go , kumsiah!Sim Lim Tower lor.
possible to tell me the exact shop and item name? wan to just grab n go , kumsiah!
You have to buy two parts then solder the wires, it's not ready made.
o cheyYou have to buy two parts then solder the wires, it's not ready made.
When I stop behind a vechile during RED light, I can't even see the licence plate number of the vechile infront of me clearly duying my playback in my laptop.
Please advise.
LAST DAY AT THE PC SHOW 2012 , If you havent got yours remember to come to us today !!
Korea brand gives you Korea quality.
Taiwan brand gives you Taiwan quality.
Its up to individual.
Normal.. China brand gives you China quality.
Korea brand gives you Korea quality.
Taiwan brand gives you Taiwan quality.
Its up to individual.
Agree!
bro when u collecting your $200 toy! Customer asking lolBought the adapters but did not have time to make them last nite as went to bed early to watch Euro 2012 now!!!
bro when u collecting your $200 toy! Customer asking lol
Maybe tmr night. I will let u know either tonight or tomorrow morning. Depends on my appointment tmr evening.
npMaybe tmr night. I will let u know either tonight or tomorrow morning. Depends on my appointment tmr evening.
Thks bro...that was fast!Bought the adapters but did not have time to make them last nite as went to bed early to watch Euro 2012 now!!!
Thks bro...that was fast!
I bought the stuff only. Not yet start work. Tonight and tmr night would not be free. Maybe thursday night free to solder the wires. Then weekend can collect liao.
Bought the adapters but did not have time to make them last nite as went to bed early to watch Euro 2012 now!!!
Make sure you run the correct size wire and fuse.
Make sure you run the correct size wire and fuse.
Yup. No need fuse lah. The cig plug inside have fuse liao. Been doing such adapters for my cars n r/c for at least 9yrs liao.
I use adapters that range from 10A till 300A DC.
Ok....I friday on leave...thks bro!I bought the stuff only. Not yet start work. Tonight and tmr night would not be free. Maybe thursday night free to solder the wires. Then weekend can collect liao.
How come most of us only care about recording on the move? Most install the camera facing front n that normally only show your fault when you rear-end someone.
Someone hitting us from the side or rear will not be captured, so really defeats the purpose.
I would also want the camera with motion sensor so it can record anyone or any car coming near in case of hit and run or vandalism.
Ah...interesting point of view. Quite true.
Yup. No need fuse lah. The cig plug inside have fuse liao. Been doing such adapters for my cars n r/c for at least 9yrs liao.
I use adapters that range from 10A till 300A DC.
The DC/cigarette light connector is designed for up to 15A.
So are the wires connected to it rated for slightly more than 15A.
Overloading will lead to heating of wires and subsequently plastic insulation may burn.
I've personally overloaded a pair of thin wires due to a short circuit.
Luckily it was outside and visible, with burnt smell.
Do be careful.
The objective of installing the camera at the front is to defend yourself against the 50-50 case like side collision due to abrupt lane change or reckless driving. Rear end case usually is straight forward, don't need to defend yourself much.Ah...interesting point of view. Quite true.
The DC/cigarette light connector is designed for up to 15A.
So are the wires connected to it rated for slightly more than 15A.
Overloading will lead to heating of wires and subsequently plastic insulation may burn.
I've personally overloaded a pair of thin wires due to a short circuit.
Luckily it was outside and visible, with burnt smell.
Do be careful.
Dont worry, I will be using at least 18 AWG wires. Safety is my paramount concern. I may not have any single cert in electrical/electronics engineering but I still do have basic electrical knowledge.
http://www.rbeelectr....com/wtable.htm
Second that. Also against reversing vehicle.The objective of installing the camera at the front is to defend yourself against the 50-50 case like side collision due to abrupt lane change or reckless driving. Rear end case usually is straight forward, don't need to defend yourself much.
Second that. Also against reversing vehicle.
that's right. Guard against kuku drivers engaging reverse gear when the light turns green. Also vehicles on neutral gears not applying brakes and rolling backwards, etc.
Last 5 promo units left.
Due to the overwhelming support for Itronics, the next shipment will be ready by 19th jun.
Cheers!
Second that. Also against reversing vehicle.
Good point too.
I'm looking for a used finevu 300 in working condition & everything in the box.
PM me for the price u looking for.
Prefer a set from shochong.
Thanks.
http://www.radardete...e-blackvue.html
Shochong, are there any RAW videos around of highest quality from each? Raw as in, not uploaded and processed via youtube? Are they better quality when watched direct from the card?
Thanks for the supportAny bro thinking of getting the new itronic but already got finevu 300.
I'm looking for a used finevu 300 in working condition & everything in the box.
PM me for the price u looking for.
Prefer a set from shochong.
Thanks.
Good point too.
Edited by Shochong, 13 June 2012 - 07:02 PM.
Is there any accessory i can buy from autobacs that can be plugged into the cigarette socket to maintain the voltage whenever we crank our engine?
its for my Marbella GPS.
Like these two:
http://www.ebay.com....=item3cbe035b4e
http://www.ebay.com....=item564aa45ffa
Is like 2 in 1 (rearview mirror + recorder) and nothing need to be stick to the windscreen.
Probably the recording might be poor but I saw the playback for HDVR-150 like not bad leh.
They dont have smart feature of auto surveillance, viewing angle & resolution are also not good enough[:(]Seems like those Car Rearview Mirror with DVR not very popular in here.
Like these two:
http://www.ebay.com....=item3cbe035b4e
http://www.ebay.com....=item564aa45ffa
Is like 2 in 1 (rearview mirror + recorder) and nothing need to be stick to the windscreen.
Probably the recording might be poor but I saw the playback for HDVR-150 like not bad leh.
Hi all,
Is there any accessory i can buy from autobacs that can be plugged into the cigarette socket to maintain the voltage whenever we crank our engine?
its for my Marbella GPS.
I dont think so. Have to DIY.
1) use a small saled lead acid battery
2) use some capacitors
How come most of us only care about recording on the move? Most install the camera facing front n that normally only show your fault when you rear-end someone.
Someone hitting us from the side or rear will not be captured, so really defeats the purpose.
I would also want the camera with motion sensor so it can record anyone or any car coming near in case of hit and run or vandalism.
Another perspective: hopefully when more drivers have these cams installed, it helps to keep our roads safer as other reckless drivers are aware that their actions maybe caught by other drivers. It may also help one another as the accident maybe capture on video by other drivers and you can use it as evident.
Pretty good comparison here between quality of BlackVue VS ITB100HD:
http://www.radardete...e-blackvue.html
Shochong, are there any RAW videos around of highest quality from each? Raw as in, not uploaded and processed via youtube? Are they better quality when watched direct from the card?
Yes, the video clips are better quality when viewed directly rather that via YouTube. At least it is for my Finevu 300
Has anyone face similar problem?
Will visit the Electrician shop that install the cameras tomorrow to see what's wrong.
Sian...............
Today, discovered both front and rear finevu cameras (bought from DVR Security Xuite?) no power after start up engine. Also ERP card reader no power. Got caught in a car park barrier - as the cash card in card reader cannot be read since no power.
Has anyone face similar problem?
Will visit the Electrician shop that install the cameras tomorrow to see what's wrong.
Sian...............
Most likely blown fuse and installer may have tapped both cameras to share the same fuse as IU. Go back to the installer and ask him to install the 2 cams separate from the fuse used by IU. You won't want to get caught inside an EPS car park again or worse still, go under an active ERP gantry with a dead IU.
Thanks for yr advice. Dissapointed with the installer quality of work, thought he should have done a better job. Also, why the fuse blow in the first place? Anyone know a good car electrician?
Think both cameras and the IU have drawn too much current at one time and that's why the fuse kaput.
Thanks for yr advice. Dissapointed with the installer quality of work, thought he should have done a better job. Also, why the fuse blow in the first place? Anyone know a good car electrician?
who is the installer?
Installer was assigned to me when I bought the cameras
then you should let us know the installer name/shop. we dun want to let this happen to other people right?
bro, will appreciate if u can contact me first to inform me about this issue instead of me not knowing anything & quoting us here.Today, discovered both front and rear finevu cameras no power after start up engine. Also ERP card reader no power. Got caught in a car park barrier - as the cash card in card reader cannot be read since no power.
Has anyone face similar problem?
Will visit the Electrician shop that install the cameras tomorrow to see what's wrong.
Sian...............
Its good to feedback so at least we know the real problem after verification.
And please provide your contact number, car license plate for verification.
I have 4 workshops now doing the installation, kindly pm me to let me know which workshop u went to.
Cheers
Edited by Shochong, 15 June 2012 - 11:08 PM.
As spoken over the phone, hope i have answered your queries.Ok Shochong, sorry should hv contacted u first. Will call u tomorrow to explain. Hope u can assist me.
Thanks:)
Edited by Chuppychup, 15 June 2012 - 11:41 PM.
Nice meeting u too bro, NICE CAR!just collected my ITB from bro Shochong , a very nice bro , feels comfortable buying from him. hopefully the appointed ws can get it fixed tml, den i will feed back on it.
Nice meeting u too bro, NICE CAR!
hahaha , thanks thanks
Remember to pm me if there is a higher capacity of Tpower ... you noe y I need it ... 
Edited by Chuppychup, 16 June 2012 - 12:13 AM.
lol np brohahaha , thanks thanks
Most likely blown fuse and installer may have tapped both cameras to share the same fuse as IU. Go back to the installer and ask him to install the 2 cams separate from the fuse used by IU. You won't want to get caught inside an EPS car park again or worse still, go under an active ERP gantry with a dead IU.
U wont get caught inside a EPS carpark lah. U still can tap ur Nets Cascard on the machine or insert it inside the machine to lift the barrier. Thatz wat MY cars do. They dont install IU in their car one.
Iam ready to collect from u...thks!U wont get caught inside a EPS carpark lah. U still can tap ur Nets Cascard on the machine or insert it inside the machine to lift the barrier. Thatz wat MY cars do. They dont install IU in their car one.
Iam ready to collect from u...thks!
Check ur PM for my address n contact.
Check ur PM for my address n contact.
I sms u...no reply...
I sms u...no reply...
Sorry, I am in the room n hp in living room. I just woke up only.
ha ha....ok thks bro!Sorry, I am in the room n hp in living room. I just woke up only.
English manual & firmware is only available from us, the authorized distributor for Itronics.Anyone know where I can download the latest ITB-100HD software and firmware in English please? The one I have is Korean so I can't really understand anything
Any illegal distribution is strictly prohibited.
That is why "illegal" source does not comes with one physical english manual & firmware updates.
Edited by Shochong, 16 June 2012 - 11:13 AM.
Whichever the way but sorry I can't give u as its against our policy.Interesting, so I'm either stuck with Korean or have to go trawling online?
Have to be fair to those who paid for their legal copies.
Hope u understand
Edited by Shochong, 16 June 2012 - 11:29 AM.
Bro i ordered one 3 pin charger of Tpower for u, reached let u know ;)I sms u...no reply...
Never tell me the price?....$10/=?Bro i ordered one 3 pin charger of Tpower for u, reached let u know ;)
Bro i ordered one 3 pin charger of Tpower for u, reached let u know ;)
Oi! Special ah?
Sibei eng ah, everytime change avatar.......
SWEE!Installed my Itronics ! its up and running now, very sleek and nice looking , day time video looks promising, still mointoring ... my windscreen got a bit of reflection
wahahah "special"Oi! Special ah?
Is your signature meant for bro bavarian???
Sibei eng ah, everytime change avatar.......
Eyh Pendek, why you now chaboat every where but TCSS?
Yeah, I got bear in my hands now, he anyhow chow, I stick finger
into where it hurts or pleasures most. Wahahaha! Ok, don't OT.
Not eng hor, it's CREATIVE!
wahahah "special"
Got plug to go direct AC ah? I haven't even open yet.
no la got its own special wall chargerGot plug to go direct AC ah? I haven't even open yet.
will order more
where got things interesting then I pop by mah........you mean you got bavarian's lunar birth dates on the bear and if you poke him, he'll feel pain miles away???Eyh Pendek, why you now chaboat every where but TCSS?
Yeah, I got bear in my hands now, he anyhow chow, I stick finger
into where it hurts or pleasures most. Wahahaha! Ok, don't OT.
Not eng hor, it's CREATIVE!
U wont get caught inside a EPS carpark lah. U still can tap ur Nets Cascard on the machine or insert it inside the machine to lift the barrier. Thatz wat MY cars do. They dont install IU in their car one.
Yes you will especially when you go in the car park when your IU is working and try to come out when your IU is not because the gantry will need to calculate the time you enter till the time you exit using your IU no. You'll get stuck even if you try to manually tap or insert your cashcard. You'll need the attendant's assistance. Personally encountered before when my IU's connection was shorted with my headlights' connection.
no la got its own special wall charger
will order more
To give to all your loyal customers? WAH HOH SAY LIOW! KUMSIAH KUMSIAH!!
where got things interesting then I pop by mah........you mean you got bavarian's lunar birth dates on the bear and if you poke him, he'll feel pain miles away???
Got a lot happening, got MU happening and durian MU also.
Bear and me go a long way. His mum couldn't pronounce my full name, Rumpelstiltskin,
everytime say sala, crumpledforeskin.
Got durian MU meh???Got a lot happening, got MU happening and durian MU also.
Bear and me go a long way. His mum couldn't pronounce my full name, Rumpelstiltskin,
everytime say sala, crumpledforeskin.
Today, discovered both front and rear finevu cameras (bought from DVR Security Xuite?) no power after start up engine. Also ERP card reader no power. Got caught in a car park barrier - as the cash card in card reader cannot be read since no power.
Has anyone face similar problem?
Will visit the Electrician shop that install the cameras tomorrow to see what's wrong.
Sian...............
could be the fuse burst..
my ciggy fuse burst 2x for past 4 days due to faulty DC connecting head.
i lazy go sim lim buy car fuse.. went autobaccs..each fuse $1.07.. gol workshop sure minimum $15..
http://www.dashcam24.com/
Hope you enjoy it.
To give to all your loyal customers? WAH HOH SAY LIOW! KUMSIAH KUMSIAH!!
on another note... I'm SERIOUSLY pissed off!
As luck would have it, I replaced my DRS1100 in a van this morning before setting off to a job, with my newly delivered (yesterday) iTronics ITB-100HD. First use, not 5 minutes later, I found myself involved in an incident. The roads were wet, I overtook a cyclist and another driver came out of a side road when I was far too close, they came out far too slowly and barely accelerated off. My van skidded and put a good dent in the bumper of a 1 month old Toyota Avensis. 99% of rear ends are the fault of the driver behind and although I'm not denying liability falls on me, I definitely believe she shouldn't have pulled out.
I didn't want to get into a roadside argument and knew the camera had it recorded. Unfortunately, I had no experience of how sensitive, or not, the camera is. I assumed with the smack, it would have recorded it and not let it be recorded over again. I also had it in my head, after ordering a 32GB SD card, that the card would hold 8 hours footage. Unfortunately the fact I was using the supplied 8GB card didn't pop into my head. I plugged it out after about 6 hours. The result, no footage! I seriously can't believe it! My first crash in my driving life, 5 minutes after installing a new dash cam, and I don't have the footage to show that maybe I won't be fully liable for what is probably a $1,500 repair job!!
I don't understand the File Deletion Method. If "Deletion by Time Order" is selected, does this mean it will even record over saved, important footage? Can't believe it! :(
Removed card has evidence, no way over write.
No prob Shochong, I understand :)
on another note... I'm SERIOUSLY pissed off!
As luck would have it, I replaced my DRS1100 in a van this morning before setting off to a job, with my newly delivered (yesterday) iTronics ITB-100HD. First use, not 5 minutes later, I found myself involved in an incident. The roads were wet, I overtook a cyclist and another driver came out of a side road when I was far too close, they came out far too slowly and barely accelerated off. My van skidded and put a good dent in the bumper of a 1 month old Toyota Avensis. 99% of rear ends are the fault of the driver behind and although I'm not denying liability falls on me, I definitely believe she shouldn't have pulled out.
I didn't want to get into a roadside argument and knew the camera had it recorded. Unfortunately, I had no experience of how sensitive, or not, the camera is. I assumed with the smack, it would have recorded it and not let it be recorded over again. I also had it in my head, after ordering a 32GB SD card, that the card would hold 8 hours footage. Unfortunately the fact I was using the supplied 8GB card didn't pop into my head. I plugged it out after about 6 hours. The result, no footage! I seriously can't believe it! My first crash in my driving life, 5 minutes after installing a new dash cam, and I don't have the footage to show that maybe I won't be fully liable for what is probably a $1,500 repair job!!
I don't understand the File Deletion Method. If "Deletion by Time Order" is selected, does this mean it will even record over saved, important footage? Can't believe it! :(
That is why some of the brothers here have 2-3 cards on standby, incident happen, remove card, insert new one in.
Removed card has evidence, no way over write.
Thatz what I do.
Hey guys, I've just found this and spent about 3 hours watching videos.
http://www.dashcam24.com/
Hope you enjoy it.
not interested
8 Gb can only last 3hours.
Edited by Shochong, 17 June 2012 - 11:31 AM.
Thatz what I do.
Same with me oso.
them once a while especially when i going to bring the current one home to view, I will
slot in the other one.
Once you met with an accident, you should plug it out :p
8 Gb can only last 3hours.
i saw the unedited reply...i see where you coming from. Am monitoring as this one has been agst you from day 1! competitor?? hmmmm....but yea, arse damn bloody sway, put camera in kena langgar...think buy insurance car sure scrap after tt
oops spotted by u!i saw the unedited reply...i see where you coming from. Am monitoring as this one has been agst you from day 1! competitor?? hmmmm....but yea, arse damn bloody sway, put camera in kena langgar...think buy insurance car sure scrap after tt
but really what... suddenly gong yi si ang moh lang here after DL published Itronics & niam about this model, den meng wu lang wu english manual & firmware ho yi bo...then now buay liao, install 5 mins & tio langar.. wu so zhun??
Mia jit wu ko leng gong car tio beh sio....
so now i type all the singlish qi kua if he liao gai...
Deletion by time order sibei straight forward yi ma buay liao gai, bo set deletion by file type mana eh tio protected. If really is jin eh. this type is user problem. bo tak user manual. Buy unauthorised set so bo english manual ma bo bian...
Wa zai si competitor la.
yi ai seng, wa eng qiu yi lo..
Wan to compete, compete fair, mai stir stir.
Need to resort to this... abit sia sway..
Mazda owner all your fault ! hahaha joking
Edited by Shochong, 17 June 2012 - 05:58 PM.
Just a few questions if anyone would be able to advise:
1) Is there absolutely any chance of recovering the footage even thought it was replaced with newer footage?
2) How can I ensure, even with a small card, this never happens again?
3) Is there an "Emergency" button anywhere on the ITB-100HD as there was on the DRS1100 where if an incident occurs, even if there's no shock to your car (imagine you see somebody else hit into a cyclist for example) you can press the button and it will save that segment and not record back over it?
4) What do I choose to ensure that shocks, emergencies etc are not recorded over ever, and the space they take up on the card can only be freed if I manually connect the card to the computer and delete the files?
5) On the file tree list, there are the letters N, E or P beside each file. I guess N = Normal, E = Emergency and P = Parking. I have about 10 consecutive E files but no shock or emergency happened in any of the footage. How are these showing as E so and if they are showing as E, then the sensitivity must be too high, but even though they are saves as Emergency files, then if the sensitivity was too high, then it must have saved the incident where I crashed as an E file, but then recorded over it!
So basically looking to have the sensitivity record only high shock events (going too fast over a speed bump for example is ok to save as a segment that can't be recorded over, but I don't want it so sensitive that it saves every tiny pothole I run over). I then want these events only deleted after I manually do so via the PC and have reviewed them and backed them up if necessary.
Good idea about having a spare SD card. I still can't believe I let it record over evidence that could potentially save me maybe $1,500!!! :(
Why would u think it was for u? Hmm..
Your settings are wrong. It would be over written by time order be it any brand of car dvr u used if u do the wrong setting.
will it be fair if u asked your seller to provide the after sale service he should provide?
Sunday watching movie now.
Cheers
Edited by Shochong, 17 June 2012 - 06:43 PM.
The DRS1100 simply left event files untouched and used the rest of the card continuously looping. You could leave it for 2 months before hooking it up to your pc and you'd still see events from weeks ago (low sensitivity). Is there a way to set the same with the ITB?
I also remember the "format from unit" function being cited as a great feature, how can I be sure I don't do this by mistake?
Also, if I have a few SD cards, does each card need to be programmed with my desired settings after being inserted into the camera, or once an SD card is opened with the software, are my chosen settings automatically applied to the SD card?
Wa zai si competitor la.
yi ai seng, wa eng qiu yi lo..
Wa lan! Your Ang Mo sibei tok kong!
wa tak liao ma 
Li eh peng you is jin eh Ang Mo Kok Ka lai eh ah?
55555555
Thanks, just saw your edits above. No matter what the product I buy, where I buy it or who I buy it from, I always prefer to ask questions about it on a public forum. This means I can do a google search anywhere to look back at the answers and it also means it will help anyone else searching for the same answers :)
As a public forum user, I can tell you no Singaporean who bothers to install a car dvr will continue using the same SD card to record 1 minute after an accident is stored on that card. (don't even talk about 2 months later)
To us that SD card will be like precious gold, locked up in a safe place so that we can prove our innocence
(and to prove to the wife that we did not waste all that money on a plaything!)
For me, the car dvr must first and foremost record clearly in day and night time. Every thing else is secondary
Firstly u did not remove the card once u met an accident, or do the appropriate settings for your first setup. All these could have been done right if your sales person provide u the correct advise or English manual. Guess that's the Pre and after sales service that u will miss out buying from online or local source.
Edited by Shochong, 17 June 2012 - 10:19 PM.
I find that pretty crazy that that's the default settings. So I should overwrite by file type now instead? I allocated 50% to Event file, 30% to normal and 20% to parking, but this is still uncertain for me, does this mean, if there's 5 hours of important events already saved, 3 hours of normal driving and 2 hours of parking, if another event occurs, it will record OVER one of the other events instead of taking up space allocated to normal? So in this case, it might be better to allocate 80% to event files?
The DRS1100 simply left event files untouched and used the rest of the card continuously looping. You could leave it for 2 months before hooking it up to your pc and you'd still see events from weeks ago (low sensitivity). Is there a way to set the same with the ITB?
I also remember the "format from unit" function being cited as a great feature, how can I be sure I don't do this by mistake?
Also, if I have a few SD cards, does each card need to be programmed with my desired settings after being inserted into the camera, or once an SD card is opened with the software, are my chosen settings automatically applied to the SD card?
oops spotted by u!
but really what... suddenly gong yi si ang moh lang here after DL published Itronics & niam about this model, den meng wu lang wu english manual & firmware ho yi bo...then now buay liao, install 5 mins & tio langar.. wu so zhun??
Mia jit wu ko leng gong car tio beh sio....
so now i type all the singlish qi kua if he liao gai...
Deletion by time order sibei straight forward yi ma buay liao gai, bo set deletion by file type mana eh tio protected. If really is jin eh. this type is user problem. bo tak user manual. Buy unauthorised set so bo english manual ma bo bian...
Wa zai si competitor la.
yi ai seng, wa eng qiu yi lo..
Wan to compete, compete fair, mai stir stir.
Need to resort to this... abit sia sway..
Mazda owner all your fault ! hahaha joking
Shochong, I just saw this, why the fark is this my fault now?
I don't take lightly to this farking pinning the blame on me when
I didn't do any thing wrong. Don't come and bloody well joke
With me, I don't take kindly to blame pinning.
Young man, you better explain yourself.
You talk to me u know me. What for i blame u sia.
Sorry if u take it so seriously ok!
Edited by Shochong, 17 June 2012 - 10:47 PM.
gey eh la!Wa lan! Your Ang Mo sibei tok kong!
Li eh peng you is jin eh Ang Mo Kok Ka lai eh ah?
55555555
I sense a little animosity towards me and I'm not sure why?
Shochong, I'm not your target customer and I'm certainly not your competition. I don't deny you offer a much better service to local English speakers in your area as would have been available through the same source from which I bought. But warranty, VAT etc are not things I can take advantage of as a potential customer based in Ireland so when there are virtually no local suppliers of this product, I must resort to purchase it online and price will be the deciding factor in who to buy with. I fully understand your extra costs and the extra benefits associated with them of buying from you, so please understand my points too.
To explain how it so happened that I managed to overwrite?
Previous user of DRS1100 and assumed iTronics would also not overwrite shock incidents.
Took delivery only the day before the accident of iTronics ITB100HD devices for use in vans.
Only briefly explored the software (still using Korean version) that night with footage from the first van I installed to, which in the time it was in use, drove for 1 hour and parked for 4 hours. Looking at the SD card, it was only 3.75/8GB used. I wasn't aware it only recorded motion sensed/shocked segments while parked, so really there was probably only 1.5 hours footage recorded to the card, not 5. I also bought additional 32GB cards from a different resource online which haven't been delivered yet. From reading recording time levels, I remember seeing a 32GB card can hold over 8 hours footage. It should be therefore pretty reasonable to believe I had it in my head, mistakenly that I'd have more than 8 hours footage before previous footage would be overwritten and also fair to believe from having used the DRS1100, that I thought the footage since it was a shock, wouldn't even be overwritten. The van which had the crash was installed with another iTronics ITB100HD first thing in the morning before I drove to a job. The DRS1100 was hardwired in and they use the same voltage and same size connector so I simply replaced it with the new unit. I had the crash 5 minutes later and as I was on the way to a job, with the above assumptions, let it record as I knew I may be still in a little shock and thought it would be good to have the camera rolling. As the my job involves loading the van with furniture etc, every minute the van was parked was pretty much recorded due to the high sensitivity level and me and customers moving around in the cargo bay loading items. After 6 hours I unplugged it as I didn't want to take any chances. Unfortunately due to my mistakes and misunderstandings above, it was too late.
Asking why I didn't go for the DRS1100's successor isn't really relevant. I wanted the best and it seemed like the ITB100HD was it. I made some assumptions about the recording and overwriting method based on my previous unit which proved to be wrong. I still believe the DRS1100's system of NEVER overwriting emergency events until deleted by the user from a computer is best to ensure nothing is deleted. I'm also very surprised there is no "emergency" button to make an incident such as seeing another car hit a cyclist be safely stored and not overwritten on the card.
I found this forum on a google search for BlackVue as I was interested in buying it. It was Shochongs posts which led me to go for the ITB100HD over the BlackVue. I believed this thread was a place to discuss various units and questions and comments about them so I decided to ask about English Software and Firmware since I only had Korean supplied with mine, typical question to ask in a discussion forum.
I don't like getting involved in lengthy discussion like this so would appreciate your understanding of my situation. If nobody answers the various questions then I'll seek the answers elsewhere as I would in any other situation :)
With regards to ur firmware, write to ur seller.
Otherwise u can use google translate from Korean to English. Or hook up with a korean
what do you guys think of Papago P1??
I wan to declare publicly that I'm not affiliated with this peep.
But yeah, i started a thread on Papago! P0, P1 and P3.
Its a good cam except that it doesnt have Parking Mode. But what it's good is that once you hit with accident, you can press a button that locked that portion of video (I think it's 1 minute before and after that accident). it is capable of locking up to 10 videos on accidents.
I wan to declare publicly that I'm not affiliated with this peep.
But yeah, i started a thread on Papago! P0, P1 and P3.
Its a good cam except that it doesnt have Parking Mode. But what it's good is that once you hit with accident, you can press a button that locked that portion of video (I think it's 1 minute before and after that accident). it is capable of locking up to 10 videos on accidents.
Nut, how much did you pay for this?
I really appreciate the work you have done, you explained everything in such an amazing and simple way. Thanks for sharing this useful blog. Eps Carpark System
Trả lờiXóa